stranissimo riavvio del pc..

**p060477** · 17-11-11, 11: 34

..quindi ad esempio con speedfan cosa faccio..??..perche' se io lo avvio mi da le temp degli hd del pc e della gpu e cpu..ma come faccio a vedere la salute del hd su cui ho la partiz C/..??

**DeST** · 17-11-11, 12: 32

Su speed fan, dalla finestra principale basta cliccare sulla scheda S.M.A.R.T. e dal menu a tendina selezionare l'HD da controllare, subito vengono visualizzate le statistiche di base che puoi anche approfondire cliccando su "esegui scansione online approfondita dell'hard disk"

ti allego un immagine
sf.jpg
se queste funzioni in speedfan non sono presenti probabilmente hai una versione datata di speedfan

**Kirk78** · 17-11-11, 12: 47

Difatti non sapevo che lo speedfan facesse anche un controllo del disco (guarda la TAB "S.M.A.R.T.").

Sicuramente, visto il nome, HDD scan lo farà di certo!

**p060477** · 17-11-11, 18: 05

cieo e grazie!!

ecco cosa ho ottenuto dalla scan profonda on line di speed fan..:

Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected by the drive itself and contains data that the manufacturer considered relevant to check reliability. The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data, and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is considered unreliable and likely to fail. By using several techniques, this report tries to give a wider range of info, basing its analysis on advanced comparisons with normal values based on real hard disks and on expert-like checks. The final results are not to be taken as an absolute truth, but they are a very good approach to what a professional would say about your hard disk status.
Your hard disk is a Maxtor 6L200M0 with firmware BANC1E00.
The average temperature for this hard disk is 37C (MIN=28C MAX=49C) and yours is 29C.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.
Your hard disk is now being compared to real data used to define normal values for your specific hard disk model. This way, the analysis can automatically use proper operating ranges. The images give you an idea of how each attribute is within such range. Current and raw values are shown for easier reference for experienced users. There are 3001 hard disk models in the current archive.

Attribute Current Raw Overall
2 Spin Up Time 207 12820 Normal
0 Start/Stop Count 252 2618 Watch
Warning: Start/Stop Count is below the average limits (253-253).
10 Reallocated Sector Count 253 0 Very good
10 Read Channel Margin 253 0 Very good
10 Seek Error Rate 253 0 Very good
10 Seek Time Performance 249 47307 Very good
0 Power On Hours Count 173 27401 Watch
Warning: Power On Hours Count is below the average limits (230-253).
10 Spin Retry Count 253 0 Very good
10 Calibration Retry Count 253 0 Very good
0 Power Cycle Count 247 2742 Watch
Warning: Power Cycle Count is below the average limits (251-253).
10 Power Off Retract Count 253 0 Very good
10 Load Cycle Count 253 0 Very good
10 Hardware ECC Recovered 253 5878 Very good
10 Reallocated Event Count 253 0 Very good
10 Current Pending Sector 253 0 Very good
10 Offline Uncorrectable Sector Count 253 0 Very good
10 Ultra DMA CRC Error Rate 199 0 Very good
10 Write Error Rate 253 0 Very good
10 Soft Read Error Rate 253 0 Very good
10 TA Increase Count 253 0 Very good
10 Run Out Cancel 253 0 Very good
10 Shock Count Write Opern 253 0 Very good
10 Shock Rate Write Opern 253 0 Very good
10 Spin High Current 253 0 Very good
10 Spin Buzz 253 0 Very good
3 Offline Seek Performance 241 154 Normal
10 Unknown attribute 210 253 0 Very good
10 Vibration During Write 253 0 Very good
10 Shock During Write 253 0 Very good

NOTE: not all warnings are reflected on fitness and performance overall values because relevancy is based upon the settings from the hard disk manufacturer who is the best entity deputed to define such relationships.

NOTE : your hard disk Power On Hours Count attribute current value (173) is below the normal range (230 - 253) reported for your specific hard disk model. Basically your hard disk was powered on for more than the maximum time the average user did. This means that either all of the reports collected are from hard disks that were not powered on for too long (this is realistic for recent models) or that your hard disk is becoming old. Usually this is not considered as a pre-failure advisory, but you should check whether you want to replace the hardware or keep an eye on its performances over time.

NOTE : your hard disk Power Cycle Count attribute current value (247) is below the normal range (251 - 253) reported for your specific hard disk model. Basically your hard disk was power cycled more times than the maximum number the average hard disk was. Power cycles put some stress on the hard disk mechanic. Sometimes power cycles can be caused by a loose hard disk power connector. Make sure it is properly fastened.

The overall fitness for this drive is 96%.
The overall performance for this drive is 96%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
DISCLAIMER: this report does its best to highlight issues and warnings related to your hard disk. It cannot be held responsible for any mistake. This page and its results cannot be used in any other way but the one defined by its author.

cosa ne pensate..??

**Kirk78** · 17-11-11, 18: 43

Ci sono 3 warning, di cui uno abbastanza basso - Power On Hours Count - di 173 quando il range vedo tra 230 e 253. L'altro tool, che fa la scansione settore per settore l'ha fatta? Attenzione che potrebbe metterci parecchio tempo.

**p060477** · 17-11-11, 18: 47

grazie!

parto con l'altro tool..!!

e' che ci mette sempre una vita..per cui speravo in speedfan..

cosa ne pensi intanto del report..??

sono preoccupanti i 3 warnings..??

e' - alla frutta-..!!??

**Kirk78** · 17-11-11, 18: 53

Quello abbastanza basso che ti dicevo mi da un'attimo da pensare.

The raw value of this attribute shows total count of hours (or minutes, or seconds, depending on manufacturer) in power-on state. A decrease of this attribute value to the critical level (threshold) indicates a decrease of the MTBF (Mean Time Between Failures).
However, in reality, even if the MTBF value falls to zero, it does not mean that the MTBF resource is completely exhausted and the drive will not function normally

Ti avevo già suggerito un backuppino ? A si vedo che li fai spesso. Come non detto.

**DeST** · 17-11-11, 19: 37

3 warning non sono tanto gravi (soprattutto contando che si basa su statistiche approssimative) per avere un idea generale lo stato viene indicato come

The overall fitness for this drive is 96%.
The overall performance for this drive is 96%.

il che dovrebbe far capire che il disco è in buone condizioni, ovviamente se vuoi maggiori dettagli meglio un tool apposito, ma io non mi preoccuperei tanto

**Eres** · 17-11-11, 20: 08

a me sembrano dei warning del tutto trascurabili per la salute del disco, anzi direi che non c'entrano nulla, L'HD è a posto

**Kirk78** · 17-11-11, 20: 20

Secondo la media degli HDD inseriti nel loro database almeno è, appunto, uno warning, sull'MTBF che comunque come detto è statistica, ma parecchio bassa. L'altro tool è sicuramente più secifico per settori. Il mio vecchio Maxtor ha inziato a diminuire abbastanza quel valore prima di soccombere, quindi qualche statistica potrebbe non essere errata.